Change font size


Post a new topicPost a reply Page 2 of 2   [ 23 posts ]
Go to page Previous  1, 2
Author Message
 Post subject: Re: 1800S Front Crossmember Repair.
PostPosted: Tue Apr 29, 2014 11:09 am 
Canadian Tire Bolt ons

Joined: Tue Aug 07, 2007 9:36 am
Posts: 29
Location: Portland, OR
Nice work, Craig!

I was going to ask how you get paint or something into the areas that are capped off now, such as the control arm cap, to protect it from rusting inside out, but maybe powder coating can get in there? Or does it not typically matter anyway?

Also, just wanted to point out that you likely won't die from having a blown shock attachment up there, you'll just have a "blown shock", aka, none, and some clunking noises. The car will still stay up because the spring is still seated properly, right?

LOOKS GOOD! Someone cross posted this in the local forums because it was such good stuff. =D>

_________________
Kyle - '91 244(DD) - '68 142(SOLD!?!) - '06 Ninja 250R


Top
 Profile  
 
 Post subject: Re: 1800S Front Crossmember Repair.
PostPosted: Tue Apr 29, 2014 4:42 pm 
Haha, I just built a W24 Octo-Turbo, now what?!
User avatar

Joined: Wed Jun 14, 2006 4:19 pm
Posts: 3131
Location: Lethbridge, AB
KLR142 wrote:
Nice work, Craig!

I was going to ask how you get paint or something into the areas that are capped off now, such as the control arm cap, to protect it from rusting inside out, but maybe powder coating can get in there? Or does it not typically matter anyway?

Also, just wanted to point out that you likely won't die from having a blown shock attachment up there, you'll just have a "blown shock", aka, none, and some clunking noises. The car will still stay up because the spring is still seated properly, right?

LOOKS GOOD! Someone cross posted this in the local forums because it was such good stuff. =D>



The capped LCA mount area is TIG welded all the way around - it's about as sealed as you can get. There is no way to get powder in there, but there is no way to get anything else in there either. At 1/8" thick - it will out live me in any event.

I know you won't die from the shock condition (it would be a bouncy ride though) but the way some repairs go on these cars, it's better to assume that fatigued metal is replaced, not re-welded. I've seen some scary stuff with lower control arms cracking under the stress of the larger bar.

_________________
Coburn Performance - OCD comes naturally.


Top
 Profile  
 
 Post subject: Re: 1800S Front Crossmember Repair.
PostPosted: Tue Apr 29, 2014 5:21 pm 
Canadian Tire Bolt ons

Joined: Tue Aug 07, 2007 9:36 am
Posts: 29
Location: Portland, OR
Right on, good deal!

_________________
Kyle - '91 244(DD) - '68 142(SOLD!?!) - '06 Ninja 250R


Top
 Profile  
 
 Post subject: Re: 1800S Front Crossmember Repair.
PostPosted: Sun Nov 19, 2017 6:10 pm 
Canadian Tire Bolt ons

Joined: Sat Nov 14, 2015 1:53 pm
Posts: 47
Hi Craig.
I’ll be rebuilding my 1800 crossmember and it would be a big help if I could see the pictures. If it’s not too much trouble, and you still have them, could you repost them, or send them to me?
Thanks.

Craig.


Top
 Profile  
 
 Post subject: Re: 1800S Front Crossmember Repair.
PostPosted: Fri Nov 24, 2017 11:02 pm 
Haha, I just built a W24 Octo-Turbo, now what?!
User avatar

Joined: Wed Jun 14, 2006 4:19 pm
Posts: 3131
Location: Lethbridge, AB
This is where I started.

Image

This is where we ended.

Image

I did cut all that nonsense metal out and replace all the fatigued stuff. Post what you have. I have to look up the other image.

_________________
Coburn Performance - OCD comes naturally.


Top
 Profile  
 
 Post subject: Re: 1800S Front Crossmember Repair.
PostPosted: Sat Nov 25, 2017 1:05 am 
Canadian Tire Bolt ons

Joined: Sat Nov 14, 2015 1:53 pm
Posts: 47
I’m expecting early next week a used replacement and will post up the photos once I get it disassembled. I plan on stripping it then having the weak points welded. Thx.


Top
 Profile  
 
 Post subject: Re: 1800S Front Crossmember Repair.
PostPosted: Mon Nov 18, 2019 9:25 pm 
Haha, I just built a W24 Octo-Turbo, now what?!
User avatar

Joined: Wed Jun 14, 2006 4:19 pm
Posts: 3131
Location: Lethbridge, AB
I'm interested to see what it looks like. There is a lot of reinforcement that should go into these things.

_________________
Coburn Performance - OCD comes naturally.


Top
 Profile  
 
 Post subject: Re: 1800S Front Crossmember Repair.
PostPosted: Tue Nov 19, 2019 11:37 pm 
Canadian Tire Bolt ons

Joined: Sat Nov 14, 2015 1:53 pm
Posts: 47
Hi, unfortunately life gets in the way, there’s been a few bumps on the road. The replacement crossmember sits in the box it arrived in. Damaged by Fedex too, and no love from them, the seller sent me 2 wishbones to make it good, and they’re still in the box too. Plan to tackle this over the winter and will keep you posted.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post a new topicPost a reply Page 2 of 2   [ 23 posts ]
Go to page Previous  1, 2


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron


Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
610nm Style by Daniel St. Jules of Gamexe.net