WANTED: 240 Radiator Core Support Volvo 240

mattcoombs · **Joined:** Fri Feb 11, 2011 11:09 pm **Posts:** 5

Hi, I hit a deer with with my '93 Volvo 240 and need a Radiator Core Support.
Even if no one has this part, I would appreciate any recomendations for wreckers in the Calgary area that might have an '86-93 240.
Thanks!

Pylon · **Posted:** Sat Feb 12, 2011 8:50 am

Pick n Pull usually has at least one later 240. IIRC there are two or three out there right now. I'm heading out there this morning and can report back with what's there...

mattcoombs · **Joined:** Fri Feb 11, 2011 11:09 pm **Posts:** 5

Thanks Pylon,
I was going to go there myself this morning, and they did have a '91 in their inventory earlier this week, but apparently it's gone to the crushers now.... doesn't show on their website's inventory anymore and that's what the guy said when I called. I don't know for sure, but I doubt a Radiator Core Support from an '81 would fit. That's all they've got there right now.
I guess I'll just have to wait.
Cheers
Matt

woodenshoes · **Posted:** Sat Feb 12, 2011 9:43 am

Do you have a link to their website listing the inventory? I can find the Navajo Metals site but I don't see any inventory tabs/buttons? Oh, welcome to CVC and good luck with your search.

mattcoombs · **Joined:** Fri Feb 11, 2011 11:09 pm **Posts:** 5

http://www.picknpull.com/check_inventory.aspx

Pylon · **Posted:** Sat Feb 12, 2011 1:08 pm

Looks to be about right. 2 '81 240 series out there right now...

mattcoombs · **Joined:** Fri Feb 11, 2011 11:09 pm **Posts:** 5

Looks like an '87 was just put out. If anyone reads this and is out there and wouldn't mind telling me what the core/rad support and driver's side front fender look like, I'd really appreciate it! It'd save me driving up there for nothing from the Crowsnest Pass.

THANKS!

122_Canuck · **Posted:** Thu Feb 17, 2011 2:30 pm

mattcoombs wrote:

Looks like an '87 was just put out. If anyone reads this and is out there and wouldn't mind telling me what the core/rad support and driver's side front fender look like, I'd really appreciate it! It'd save me driving up there for nothing from the Crowsnest Pass.

THANKS!

There's a few 240's at the Lethbridge PYP - core supports are all fine. Fenders are rusty.

volvoshredder · **Posted:** Thu Feb 17, 2011 3:07 pm

The two there are both early cars though. Not sure if those fit.

122_Canuck · **Posted:** Thu Feb 17, 2011 6:45 pm

The core support would be the same no? Fenders not - but they are all nasty IIRC.

volvoshredder · **Posted:** Thu Feb 17, 2011 6:50 pm

I'm not sure. I've never looked too close at the later one.

rockmonton · **Posted:** Thu Feb 17, 2011 11:43 pm

core supports do not interchange because the bottom panel differs for the different lights.

I THINK i have one in the garage, but i'm also in edmonton, your call.

mattcoombs · **Joined:** Fri Feb 11, 2011 11:09 pm **Posts:** 5

Oh really, one in Edmonton. My fiance is there, so I'm there often enough. Could you check if you have it? How much would you want for it? My car is a 1993 240 (wagon)

rockmonton · **Posted:** Sat Feb 19, 2011 6:32 pm

had a quick look, i found the horns that were attached to it, so i'm not so sure it's still kicking around, but i'll keep an eye out for it.

with any luck it'll turn up.

edit:

Found an early one in the garage today, no luck yet on a late-model one though.

Pylon · **Posted:** Fri Feb 25, 2011 8:28 pm

Looks like 2 later 240 series cars put out this week...

WANTED: 240 Radiator Core Support Volvo 240

Who is online